Meter Selection Utility


Answer nine simple questions about your application to find the exact meter you need.
Don't know the answer to some of the questions? Just fill out what you know!

Displaying 111 total products (page 4 of 12):

  • The PD6300 is a member of the ProVu series of 1/8 DIN digital panel meters that is specifically designed to display flow rate and total from a pulse output (NPN, PNP, TTL, switch contact, sine wave, etc.) flowmeter. It displays that signal on a dual-line, 6-digit display that is available with optional Sunbright® sunlight readable LEDs. Flow rate is typically displayed on the upper line and the cumulative total is displayed on the lower line. The total overflow feature allows up to a 9-digit total and grand total to be displayed. Like all ProVu meters, the PD6300 includes UL / C-UL listing and CE marking, a NEMA 4X front, and AC or DC power options. ProVu meters can be equipped with up to four internal relays, a 4-20 mA output, and Modbus® RTU serial communications. The PD6300 includes a 24 VDC power supply to drive the flowmeter and can be programmed via the front panel pushbuttons or free MeterView® Pro software.

    Why you should buy:
  • Go with the Helios PD2-6300 when you want to display both flow rate and total at the same time from a pulse output flowmeter. The PD2-6300 can display both flow rate and total in six full digits and can also be configured to display non-resettable grand total. The PD2-6300's NEMA 4X enclosure, super bright LEDs, and wide operating temperature range make it perfect for outdoor applications.

     

     

     

    Why you should buy:
    • Large Dual Line Display
    • Displays Flow Rate and Total
    • Pulse Input
  • The PD663 is a loop-powered field meter that is CSA Certified as Explosion-Proof, Dust-Ignition-Proof, and Flame-Proof, and ATEX & IECEx Certified as Explosion-Proof. It is available in either an aluminum or stainless steel enclosure with ¾" or M20 connections. The PD663 is easy to install and program and it can be seen in a variety of lighting conditions, even in bright sunlight. It will operate down to -40°C and is approved for installation in areas where the temperature gets as cold as -55°C, however the display will cease functioning.


  • The Vantageview PD6700 is one of Precision Digital's most advanced and feature-packed plastic, field-mounted, loop-powered indicators. The fact that this meter is loop-powered means that there is no need to run additional, costly power lines. The PD6700 is built in a NEMA 4X and IP65 rated plastic enclosure which can stand up to even the harshest environmental conditions. It features a dual-line display that can be easily scaled in the field for any 4-20 mA analog input. The display has a five digit upper display, a seven alpha-numeric character lower display, and comes with a backlight standard. Two features that really make the PD6700 stand out are its wide viewing angle display and SafeTouch® through-window buttons. These buttons allow the meter to be programmed and operated through the cover window, thus eliminating the need to remove the cover in dirty or wet environments.

    Why you should buy:
    • NEMA 4X/IP65 Enclosure
    • Loop-Powered
    • Level Indication Bargraph Display
  • The PD6908-GP loop-powered process meter and PD6907-GP feet & inches level meter include a NEMA 4X, IP66 plastic enclosure and can be installed in a variety of harsh operating environments to provide convenient and informative display of any 4-20 mA signal. One of the most convenient features of these instruments is their dual-line display which is typically used to display the process variable on the 5-character alphanumeric top display and the units of measure or a tag on the 8-character alphanumeric bottom display. The feet & inches models display level in feet and inches on the top display and the bottom 8-character alphanumeric display can be used to display a tag or custom message.

    The VantageView+'s 14-segment alphanumeric characters on the bottom display line provide a much clearer indication of tags, units, or alarm messages than 7-segment characters do.

    Further enhancing the display on these instruments is a 20-segment bargraph.

    The four CapTouch through-window buttons located on the front of the meter provide a convenient way to operate the meter without removing the cover.

    Free, PC-based, MeterView XL software that connects to the meter via a micro USB cable is available for programming and setup of the meters.

     

    Why you should buy:
    • Dual-Line Backlit LCD Display
    • Operate to -40°C; Install to -55°C
    • Loop-Powered
    • Plastic NEMA 4X Enclosure
    • Flashing Red Display / Message on Alarm
    • CapTouch Through-Window Programming
    • 1.5 Volt Drop
    • Free Programming Software
    • Bargraph or Feet & Inches Display
    • Discrete and Analog Output Options
  • The Sabre P PD603 process meter combines operational simplicity with high end features to deliver the perfect low-cost 1/8 DIN digital panel meter for display only applications. The PD603’s menu structure is easy to navigate because the only selections are for input, decimal point location, and scaling values; there are no other menu choices to add confusion during the setup process. Despite being a low-cost meter, the PD603 is still packed with many features typically found only on more expensive meters, such as a NEMA 4X front, universal power supply, front panel programming, input current overload protection, UL listing, and CE marking.


    Why you should buy:
    • Low Cost Display Only Option
    • NEMA 4X/IP65 Front
    • Analog Input
  • Go with the Helios PD2-6100 when you have a weighing application where you need to read the display from a distance, or outside in the bright sunlight in temperatures between -40 to 150°F. The PD2-6100 tare feature can be used to remove the weight of the container from the weight calculation. You can even re-transmit the weight signal with the PD2-6100's optional 4-20 mA output.

     

     

     

     

    Why you should buy:
    • Large Dual Line Display
    • Load Cell and mV
    • Dual Scale Weight and Volume
  • The PD6938 ProtEX+ pulse input flow rate/totalizers can be installed in a variety of areas (hazardous, dirty, wet, corrosive, hot, or cold) to provide convenient and informative display of flow rate and total from any pulse output flowmeter. These instruments will accept a variety of pulse inputs, including slow pulse rates. They can be powered from a battery, 9-30 VDC, or the 4-20 mA output loop, have on-board datalogging capabilities, come with explosion-proof approvals, and can be ordered with optional 4-20 mA output and two relays.

    The PD6938 can operate down to -40°C and is certified by the agencies to be installed in areas that get as cold as -55°C.

    The PD6938 ProtEX+ is available in aluminum and stainless steel enclosures that are designed for easy use and installation. The process connection is available in M20, 3/4" NPT and 1" NPT and there are two other conduit holes for field wiring.

    Free, PC-based, MeterView XL software that connects to the meter via a micro-USB cable is available for programming and setup of the instruments. Four CapTouch through-window buttons are available to operate the instrument without removing the cover.

    All models come equipped with two open collector outputs and a digital input. There are also models available with Modbus RTU RS-485 communications, two solid-state relays, and isolated 4-20 mA analog output options.

  • The PD6928-GP loop-powered flow rate/totalizers include a NEMA 4X, IP66 plastic enclosure and can be installed in a variety of harsh operating environments to provide convenient and informative display of any 4-20 mA signal. One of the most convenient features of these instruments is their dual-line display which is typically used to display the flow rate on the 5-character alphanumeric top display and flow total, flow grand total, or a tag on the 8-character alphanumeric bottom display. The top display uses 12-segment, and the bottom display uses 14-segment alphanumeric characters for clear indication of tags, units, or alarm messages.

    Further enhancing the display on these instruments is a 20-segment bargraph.

    The four CapTouch through-window buttons located on the front of the meter provide a convenient way to operate the meter without removing the cover.

    Free, PC-based, MeterView XL software that connects to the meter via a micro USB cable is available for programming and setup of the meters.

     

     

     

     

     

     

    Why you should buy:
    • Dual-Line Backlit LCD Display
    • Operate to -40°C; Install to -55°C
    • Loop-Powered Rate / Totalizer
    • Display Rate & Total Simultaneously
    • Plastic NEMA 4X Enclosure
    • Flashing Red Display / Message on Alarm
    • CapTouch Through-Window Programming
    • 1.5 Volt Drop
    • Free Programming Software
    • Discrete and Analog Output Options
  • The PD6938 VantageView+ pulse input flow rate/totalizers can be installed in a variety of areas (dirty, wet, corrosive, hot, or cold) to provide convenient and informative display of flow rate and total from any pulse output flowmeter. These instruments will accept a variety of pulse inputs, including slow pulse rates. They can be powered from a battery, 9-30 VDC, or the 4-20 mA output loop, have on-board datalogging capabilities, and can be ordered with optional 4-20 mA output and two relays. The PD6938, with the addition of its two optional relays, can also be used as a simple batch controller.

    The PD6938 VantageView+ comes in a NEMA 4X, IP66 plastic enclosure that is designed for easy use and installation. There are three 3/4" NPT threaded conduit holes available for wiring. Two 3/4" NPT plastic conduit plugs are included.

    Free, PC-based, MeterView XL software that connects to the meter via a micro-USB cable is available for programming and setup of the instruments. Four CapTouch through-window buttons are available to operate the instrument without removing the cover.

    All models come equipped with two open collector outputs and a digital input. There are also models available with Modbus RTU RS-485 communications, two solid-state relays, and isolated 4-20 mA analog output options.