Display: Upper display: 0.60" (15 mm) high. Lower display: 0.46" (12 mm) high. Both are 6 digits (-99999 to 999999), red LEDs.
Resolution: 1° (up to four digits) or 0.1° (up to five digits)
Display Intensity: Eight intensity levels
Display Update Rate: 5/second (200 ms)
Front Panel: NEMA 4X, IP65
Programming Methods:Four front panel buttons, digital inputs, PC and MeterView Pro software, Modbus registers.
F4 Digital Input Contacts: 3.3 VDC on contact. Connect normally open contacts across F4 to COM.
F4 Digital Input Logic Levels: Logic High: 3 to 5 VDC Logic Low: 0 to 1.25 VDC
Noise filter: Programmable from 2 to 199 (0 will disable filter)
Filter Bypass: Programmable from 0.1 to 99.9% of span
Recalibration: Recommended at least every 12 months.
Max/Min Display: Max / min temperature readings are stored until reset by the user or until power to the meter is cycled.
Non-Volatile Memory: All programmed settings are stored in nonvolatile memory for a minimum of ten years if power is lost.
Power Options:85-265 VAC 50/60 Hz, 90-265 VDC, 20 W max or 12-24 VDC ± 10%, 15 W max. Powered over USB for configuration only.
Normal Mode Rejection: Greater than 65 dB at 50/60 Hz
Isolation: 4 kV input/output-to-power line. 500 V input-to-output
Operating temperature range: -20 to 65°C
Storage temperature range: -40 to 85°C
Relative humidity: 0 to 90% non-condensing
Connections: Removable screw terminal blocks accept 12 to 22 AWG wire, RJ45 for external relays, digital I/O, and serial communication adapters.
Enclosure: 1/8 DIN, high impact plastic, UL 94V-0, color: black (92 mm x 45 mm). Two panel mounting bracket assemblies are provided.
Dimensions: 4.68" x 2.45" x 5.64" (119 mm x 62 mm x 143 mm) (W x H x D)
Weight: 9.5 oz (269 g)
UL File Number: UL & c-UL Listed. E160849; 508 Industrial Control Equipment.
Warranty: 3 years parts & labor
USB Connection: Compatibility: USB 2.0 Standard, Compliant
Connector Type: Micro-B receptacle
Cable: USB A Male to Micro-B Cable
Driver: Windows 98/SE, ME, 2000, Server 2003/2008, XP 32/64-Bit,
Vista 32/64-Bit, Windows 7 32/64-Bit, Windows 10 32/64-Bit
Power: USB Port
Thermocouple J, K, T, E, R, S, B, N, C; RTD 100 Ω platinum (0.00385 & 0.00392 curves), 10Ω copper, 120Ω nickel, 1000Ω platinum Input Impedance:
Greater than 100 kΩOffset Adjust:
User programmable offset adjust ±50.0 degreesTemperature Drift:
±2°C maximum from 0 to 65°C ambient temperature; ±4°C maximum from -20 to 0°C ambient temperatureSensor Break:
Display flashes "Open", relays can be programmed to go "On", "Off", or to "Ignore" (detected as an upscale condition).Averaging:
Up to 10 RTDs connected in parallel can be averaged.Accuracy & Range:
|Type|| Range (°F)|| Range (°C)||Accuracy|
|J|| -200 to 2000|| -129 to 1093||±1°C|
|K|| -200 to 2400|| -129 to 1316||±1°C|
|T|| -200 to 752||-129 to 400||±1°C|
|E|| -200 to 1800||-129 to 982||±1°C|
|R|| -50 to 3000|| -46 to 1649||±2°C|
|S|| -50 to 3000|| -46 to 1649||±2°C|
|B|| 752 to 3300|| 400 to 1816||±2°C|
|N|| -100 to 2300|| -73 to 1260||±2°C|
|C|| 32 to 4100|| 0 to 2260||±2°C|
|10 Ω|| -328 to 500|| -200 to 260||±0.1°C|
|100 Ω|| -328 to 1562|| -200 to 850||±0.4°C|
|120 Ω|| -110 to 500|| -79 to 260||±0.1°C|
|1000 Ω|| -328 to 900|| -200 to 482||±0.4°C|
2 or 4 SPDT (Form C) internal and/or 4 SPST (Form A) external; rated 3 A @ 30 VDC and 125/250 VAC resistive load; 1/14 HP (≈ 50 watts) @ 125/250 VAC for inductive loads such as contactors, solenoids, etc.Noise Suppression:
Noise suppression is recommended for each relay contact switching inductive loads.Deadband:
0-100% of span, user programmableHigh or Low Alarm:
User may program any alarm for high or low trip point. Unused alarm LEDs and relays may be disabled (turned off).Relay Operation:
automatic (non-latching), latching (requires manual acknowledge), sampling (based on time), pump alternation control (2 to 8 relays), Off (disable unused relays and enable interlock feature, manual on/off control mode).Time Delay:
0 to 999.9 seconds, on & off relay time delays. Programmable and independent for each relay. Fail-Safe Operation:
Programmable and independent for each relay.Note: Relay coil is energized in non-alarm condition. In case of power failure, relay will go to alarm state. Auto Initialization:
When power is applied to the meter, relays will reflect the state of the input to the meter.
Isolated 4-20 mA Transmitter OutputOutput Source:
PV (temperature), max, min, set points 1-8, manual control setting, or Modbus inputScaling Range:
1.000 to 23.000 mA for any display range Calibration:
Factory calibrated 4-20 mA outputAccuracy:
±0.1% of span ± 0.004 mATemperature Drift:
0.4 µA/°C max from 0 to 65°C ambient, 0.8 µA/°C max from -40 to 0°C ambientNote: Analog output drift is separate from input drift.Isolated Transmitter Power Supply:
Terminals I+ & R: 24 VDC ± 10%. Isolated from the input at >500 V. May be used to power the 4-20 mA output or other devices. All models rated @ 40 mA max.External Loop Power Supply:
35 VDC maximumOutput Loop Resistance:
|24 VDC||10 Ω||700 Ω|
|35 VDC (external)||100 Ω||1200 Ω|
RTUMeter Address/Slave ID:
1 - 247Baud Rate:
300 - 19,200 bpsTransmit Time Delay:
Programmable between 0 and 199 ms or transmitter always on for RS-422 communicationData:
8 bit (1 start bit, 1 or 2 stop bits)Parity:
Even, odd, or none with 1 or 2 stop bitsByte-to-Byte Timeout:
0.01 - 2.54 secondsTurn Around Delay:
Less than 2 ms (fixed)Note: Refer to the PD6000/PD7000 Modbus Register Tables for details, available in Documentation
Digital I/O Expansion ModuleChannels:
4 digital inputs & 4 digital outputs per moduleSystem:
Up to 2 modules for a total of 8 inputs & 8 outputsDigital Input Logic: High:
3 to 5 VDC Low:
0 to 1.25 VDCDigital Output Logic: High:
3.1 to 3.3 VDC Low:
0 to 0.4 VDCSource Current:
10 mA maximumSink Current:
1.5 mA minimum+5 V Terminal:
To be used as pull-up for digital inputs only.
4-Relay Expansion ModuleRelays:
Four Form A (SPST) rated 3 A @ 30 VDC and 125/250 VAC resistive load; 1/14 HP (approx. 50 watts) @ 125/250 VAC for inductive loads.