Precision Digital Logo
  • PD6870 ProtEX-FarVu Explosion-Proof Large Display Loop-Powered Meter

    The ProtEX-FarVu PD6870 is a rugged, explosion-proof, loop-powered meter with 1" display digits ideal for demanding applications in hazardous areas or in the harshest environmental conditions.

    The ProtEX-FarVu carries all major approvals including:

    •  UL Listed as Explosion-Proof / Dust Ignition-Proof / Flame-Proof
    •  CSA Certified as Explosion-Proof / Dust Ignition-Proof / Flame-Proof
    •  ATEX and IECEx Certified as Explosion-Proof

    The PD6870 is available in either an aluminum or stainless steel enclosure with ¾" or M20 connections. It will operate down to -40°C and is approved for installation in areas where the temperature gets as cold as -55°C, however, the display will cease functioning.

    Why you should buy:
  • PD6830 ProtEX-RTP Explosion-Proof Pulse Input Flow Rate/Totalizer

    The ProtEX-RTP PD6830 is an explosion-proof flow rate/totalizer that can display flow rate and total from a pulse output flowmeter. Its display has a five digit upper line for rate, a seven alpha-numeric character lower line for total, and comes standard with a backlight.

    The ProtEX-RTP carries all major approvals including:

    •  FM Approved as Explosion-Proof / Dust Ignition-Proof / Flame-Proof •  CSA Certified as Explosion-Proof / Dust Ignition-Proof / Flame-Proof •  ATEX and IECEx Certified as Explosion-Proof

    It can be powered from an included battery or a 24 VDC external power supply. Some features that really make the PD6830 flow rate/totalizer stand out are its automatic unit conversions from flowmeter k-factor units, ability to log up to 1024 data points, and SafeTouch through-glass buttons. These buttons allow the PD6830 to be programmed and operated through the glass, thus eliminating the need to remove the cover in a hazardous area.

    Why you should buy:
  • PD6830X ProtEX-MFI Explosion-Proof Modbus Scanner

    The ProtEX PD6830X is an explosion-proof, RS485 serial input Modbus® RTU scanner capable of scanning up to 16 Modbus variables and displaying them on an easy-to-read, dual-line, LCD display. This Modbus scanner can be programmed as a Modbus RTU master, slave, or snooper. The PD6830X is available in two upper display line configurations: 5-digit decimal display and feet & inches display with bar graph. The lower line is the same for both versions and consists of seven alphanumeric characters.

    The ProtEX PD6830X carries all major approvals including:

    •  FM Approved as Explosion-Proof / Dust Ignition-Proof / Flame-Proof •  CSA Certified as Explosion-Proof / Dust Ignition-Proof / Flame-Proof •  ATEX and IECEx Certified as Explosion-Proof

    Two features that really make the PD6830X stand out are its wide viewing angle display and SafeTouch through-glass buttons. These buttons allow the PD6830X to be programmed and operated through the glass, thus eliminating the need to remove the cover in a hazardous area.

    Why you should buy:
  • PD6100 ProVu Strain Gauge, Load Cell & mV Digital Panel Meter

    The PD6100 is a member of the ProVu series of 1/8 DIN digital panel meters that accepts strain gauge & load cell inputs and mV signals up to 300 mV (unipolar) and ± 250 mV (bipolar) for weight indication and force measurement applications. With a max output current of 350 mA at 10 V, it can support up to twelve (12) 350 Ω load cells (minimum load resistance of 28 Ω), making it ideal for multipoint weight measurement applications. The PD6100's dual-line display and powerful dual-scale capability allows the measurement to be displayed in two different units of measure; gallons (volume) could be displayed on the upper line while pounds (weight) is displayed on the lower line, for example. Another use for the PD6100’s dual-line display is to simply show the units of measure on the bottom line. The PD6100 stain gauge meter includes a 24 VDC power supply to drive the sensors and can be equipped with up to four internal relays and two 4-20 mA outputs.

    Why you should buy:
  • PD685 Intrinsically Safe Type 4X, IP67 Loop-Powered Meter

    The PD685 is an easy to use, loop-powered indicator, certified by CSA, ATEX and IECEx as intrinsically safe. The PD685 carries international certifications under both the Class/Division System and Zone System, and is thereby suitable for use in gas and dust hazardous areas worldwide. For Division 2 applications where intrinsically safe interfaces are not needed, the PD685 is able to be installed without barriers! To achieve this ability, the PD685 underwent a special 'nonarcing assessment' under the UL 121201 and CSA C22.2 No. 213 standards, and was determined to be a device incapable of causing an ignition on its own. The PD685 is wellsuited for both indoor and outdoor applications and carries a variety of environmental ratings, including NEMA 4, Type 4X and IP67.

    The PD685 can be seen from considerable distance in bright sunlight or dimly lit areas when the standard backlight feature is activated. The fact that this meter is loop-powered means that there is no need to run additional, costly power lines into a hazardous area. The meter gets all of the power it needs from the 4-20 mA loop and its 1 V (4 V with backlight) drop results in a minimal burden on the loop. The meter features a wide -40 to 75°C operating temperature range and is available with a ½" conduit hole in a location of your choice for easy installation. Calibration is a quick two-step process involving the adjustment of only two sets of coarse and fine, non-interacting potentiometers.


    Why you should buy:
  • PD2-7000 Helios Temperature Meter

    Go with the Helios PD2-7000 when you want to display temperature on a large display meter you can see from a distance. The PD2-7000 can accept a variety of thermocouples and RTDs and displays temperature on a six digit display. The PD2-7000's NEMA 4X enclosure, super bright LEDs, and wide operating temperature range make it perfect for outdoor applications.

     

     

     

     

    Why you should buy:
  • PD6730 Vantageview NEMA 4X Pulse Input Rate/Totalizer

    The Vantageview PD6730 is a plastic, field-mounted flow rate/totalizer that can display flow rate and total from a pulse output flowmeter. Its display has a five digit upper line for rate, a seven alpha-numeric character lower line for total, and comes standard with a backlight. The PD6730 is built in a NEMA 4X and IP65 rated plastic enclosure which can stand up to even the harshest environmental conditions. It can be powered from an included battery or a 24 VDC external power supply. Some features that really make the PD6730 stand out are its automatic unit conversions from flowmeter k-factor units, ability to log up to 1024 data points, and SafeTouch® through-window buttons. These buttons allow the PD6730 to be programmed and operated through the cover window, thus eliminating the need to remove the cover in dirty or wet environments.

    Why you should buy:
    • NEMA 4X/IP65 Enclosure
    • Battery or Line-Powered
    • Pulse Input
    • Displays Rate & Total
  • PD6730X Vantageview NEMA 4X Modbus Scanner

    The Vantageview PD6730X is a plastic, field-mounted, RS485 serial input Modbus® RTU scanner capable of scanning up to 16 Modbus variables and displaying them on an easy-to-read, dual-line, LCD display. It can be programmed as a Modbus RTU master, slave, or snooper. The PD6730X is available in two upper display line configurations: 5-digit decimal display and feet & inches display with bar graph. The lower line is the same for both versions and consists of seven alphanumeric characters. Two features that really make the PD6730X stand out are its wide viewing angle display and SafeTouch® through-window buttons. These buttons allow the PD6730X to be programmed and operated through the cover window, thus eliminating the need to remove the cover in dirty or wet environments.


    Why you should buy:
    • NEMA 4X/IP65 Enclosure
    • Modbus Input
    • Through-Window Buttons
    • Scan up to 16 PVs